제품소개

제품소개

USB-1210

ㆍ▷ 4-CH 16-Bit 2MS/s Simultaneous-Sampling USB DAQ Module

ㆍ▷ USB 2.0 Hi-speed, USB bus power

ㆍ▷ 500VDC Isolation & 256M samples FIFO

ㆍ▷ Analog and digital triggering

Manual

Data sheet

Features
● USB 2.0 Hi-speed
● USB bus power
● 500VDC Isolation
● 256M samples FIFO
● 4-CH simultaneous-sampling analog input, 
    up to 2MS/s per channel
● Analog and digital triggering
● Removable screw terminals on module
● Lockable USB cable for secure connectivity
● Analog and digital triggering
● Ready-to-use testing application (U-Test) provided

Specification & Introduction
 Analog Input
● Resolution 
    16-Bit
● Number of channels 
    4 differential (simultaneous-sampling)
● Maximum sampling rate 
    2MS/s per channel
● Programmable gain 
    1, 5
● Input range (Voltage) 
    ± 10 V, ± 2 V
● Offset error 
    ± 1mV (gain=1)
    ± 0.2mV (gain=5)
● Gain error 
    Typical: ± 0.01% of FSR (gain=1 & 5)
    Maximum: ± 0.02% of FSR (gain=1 & 5)
● -3dB Bandwidth 
    600 kHz
● CMRR (fin=1 kHz) 
    80 dB (gain=1)
    90 dB (gain=5)
● SFDR (fin=10 kHz) 
    98 dB (gain=1 & 5)
● SINAD (fin=10 kHz) 
    89 dB (gain=1 & 5)
● THD (fin=10 kHz) 
    -100 dB (gain=1 & 5)
● SNR (fin=10 kHz) 
    89 dB (gain=1 & 5)
● ENOB (fin=10 kHz) 
    14.3-bit (gain=1 & 5)
● FIFO buffer size 
    256M Samples
● Trigger sources 
    Software, external digital, analog trigger ( from one analog input channel)
● Trigger mode 
     Post trigger, pre-trigger, delay trigger, middle trigger, gate trigger, 
    post or delay trigger with re-trigger
● External A/D conversion source 
    Yes (from CONV)
● Input coupling 
    DC
● Overvoltage protection 
    Power on: ± 35 V
    Power off: ± 15V
● Input impedance 
    1 GΩ
● Data transfer 
    Programmed I/O, continuous (USB bulk transfer mode)
 Function I/O
● Mode* 
    Digital I/O, general timer/counter, pulse generation
● Digital I/O 
    8 DI / 4 DO (TTLLVTTL level)
● General timer/counter 
    Two 32-bit, base clock: 80 MHz, external to 10 MHz
● Pulse generation 
    Two PWM outputs (Modulation frequency: 0.01 Hz to 5 MHz; duty cycle: 1%-99%)
 General Specifications
● Interface 
    USB 2.0 high speed
● I/O connector 
    Two 20-pin removable screw terminals
● Operating temperature 
    0 to 55°C (32 to 131°F)
● Storage temperature 
    -20 to 70°C (-4 to 158˚F)
● Relative humidity 
    5 to 95% non-condensing
● Power requirements 
    5V@ 500 mA (USB bus powered)
● requirements 
    114 mm (H) x 156.5 mm (L) x 41.3 mm (W) (4.5” x 6.16” x 1.63”) 
    (without connector and stand)

Ordering Information
● USB-1210
    4-CH 16-Bit 2MS/s Simultaneous-Sampling Analog
    Input USB Module